Kumaha Setup na Paké CNC Mesin router na CO2 Combo Mesin Laser? - Pidéo

Indéks pidéo:

00:00:00,000 - 00:00:03,000

Halo sadayana.

00:00:03,000 - 00:00:09,089

Hayu urang demonstrate kumaha setelan na make mesin CNC router na CO2 mesin laser combo?

00:00:13,151 - 00:01:39,412

Pariksa sagala asesoris jeung mesin CNC router laser:

a. 2 pompa cai-daya low: Hiji dipaké pikeun cooling spindle sarta séjén pikeun cooling tube laser.

b. Hiji pompa cai-daya tinggi dipaké pikeun cooling alat.

c. Hiji pompa hawa leutik dipaké pikeun niup nozzle nalika laser ukiran sarta motong.

d. Hiji tube laser, pariksa iket, ngahubungan kami pikeun exchanging dina waktu nalika eta ruksak.

e. Kotak alat kalebet CNC router controller (DSP), sensor alat, manual pangguna, rengkuh allen, saklar wates cadang, sababaraha jinis panyekel alat, rengkuh spindle, sareng piring tekanan bahan.

00:01:52,185 - 00:02:00,047

Nyusun ranté sered di sisi (éta dipiceun kusabab syarat pangiriman).

00:02:22,457 - 00:02:25,378

Bracket pikeun ngalereskeun ranté.

00:02:52,983 - 00:02:56,289

Sambungkeun ranté ka luhur.

00:03:18,043 - 00:03:22,766

Candak kaluar tabung laser sarta ngumpul eta dina bracket nu.

00:03:45,987 - 00:03:50,609

Pariksa lamun outlet tube laser beresih.

00:03:53,257 - 00:03:58,284

Tunjukkeun lampu kaluar tina tabung laser ka arah pemantul.

00:04:18,488 - 00:04:24,933

Jarak antara tube laser jeung eunteung téh ngeunaan 100-200mm.

00:04:40,054 - 00:04:48,422

Sambungkeun pipa cai cooling.

Dip selang jeung pelumas atawa cai tur sambungkeun pinuh selang ka panganteur dina.

00:04:52,204 - 00:04:58,516

Lajeng ngahurungkeun tube laser supados inlet cai ka handap sarta outlet cai ka luhur.

00:05:07,999 - 00:05:12,621

Nempatkeun bolu lemes kana bracket jeung ngalereskeun tube laser.

00:05:31,083 - 00:05:40,767

Sambungkeun garis tegangan tinggi tina catu daya laser ka tungtung tegangan tinggi tina tube laser. (Posisi asupan cai)

00:05:54,319 - 00:05:58,536

Saatos tightening, ngumpul panutup karét.

00:06:06,318 - 00:06:11,041

Nyusun garis tegangan low dina posisi kaluar laser.

00:06:31,529 - 00:06:38,784

Saatos laser dirakit sarta dibereskeun.

Pasang panutup pelindung sakabéh.

00:08:24,624 - 00:08:28,639

Nyusun DSP controller jeung alat sensor.

00:08:49,531 - 00:08:53,951

Lebetkeun kawat sinyal ti sisi katuhu kotak kontrol.

00:09:01,174 - 00:09:04,075

Selapkeun port jeung ngalereskeun.

00:09:21,222 - 00:09:25,540

Nyusun controller jeung tighten screws ngaropéa.

00:09:37,827 - 00:09:44,373

Nyusun pompa cai cooling tina spindle jeung cooling pompa cai tina tube laser.

00:10:13,162 - 00:10:17,683

Panyambung pipa cai nyambungkeun outlet pompa cai.

00:10:28,248 - 00:10:31,959

Teundeun kana wadah cai anu cai beresih.

00:10:39,993 - 00:10:47,263

Sakumpulan pipa cai beureum. Ieu nyambungkeun inlet cai jeung outlet tina aci utama.

00:10:47,263 - 00:10:55,834

Sambungkeun salah sahiji pipa cai ka pompa cai.

Teu ngabedakeun antara inlet jeung outlet cai.

00:10:56,395 - 00:11:01,625

Nempatkeun nu séjén dina tank cai.

00:11:02,572 - 00:11:07,802

Paké pompa cai sejen pikeun nyambungkeun pipa cai tina tube laser.

00:11:10,469 - 00:11:16,813

Pipa cai tina tube laser ngabedakeun pipa inlet cai jeung pipa outlet cai.

00:11:17,237 - 00:11:24,796

Lamun pipa cai dirakit sabalikna.

Tabung laser moal jalan.

00:11:35,478 - 00:11:40,202

Aya stop kontak kakuatan pikeun pompa cai di sisi kénca mesin laser router CNC.

00:11:50,046 - 00:11:57,605

Nyusun pompa cai kakuatan tinggi.

Fungsina nyaéta pikeun niiskeun alat nalika motong atanapi ngukir batu.

00:12:20,027 - 00:12:22,771

Nempatkeun eta dina tilelep dina tungtung mesin CNC.

00:12:31,221 - 00:12:37,475

Sambungkeun éta pipa cai kandel ka pompa cai badag.

Ngan hiji pipa cai kandel.

00:12:38,331 - 00:12:42,155

Nalika ngukir atanapi motong batu, hurungkeun pompa ieu.

00:12:57,512 - 00:13:01,201

Sambungkeun catu daya anu cocog kana mesin.

00:13:10,955 - 00:13:19,325

Mesin dibagi kana 380 volt. LLLN, 3 kawat panas sareng kawat nétral.

00:13:24,309 - 00:13:38,978

220 volt. LN, kawat panas sareng kawat nétral.

(Catetan yén teu 110V L N. mesin ieu teu ngarojong tegangan 110V).

00:13:47,079 - 00:13:52,838

Jeung 3 220 volt, LLL, 3 kawat panas.

00:14:07,300 - 00:14:10,584

Hurungkeun searah jarum jam pikeun ngaleupaskeun E-stop

00:14:15,619 - 00:14:18,215

Di kénca nyaéta switch kakuatan mesin.

00:14:19,444 - 00:14:24,387

Nalika saklar 2nd nunjuk ka kénca, éta dina modeu router CNC.

00:14:25,159 - 00:14:28,527

Nalika saklar nunjuk ka katuhu, éta dina modeu laser.

00:14:29,704 - 00:14:35,952

Urang 1st nunjuk kana modeu router CNC. Lajeng ngahurungkeun mesin.

00:14:39,945 - 00:14:45,119

Saatos controller dimimitian. Pencét heula tombol "Batalkeun".

00:14:45,839 - 00:14:53,347

Lebetkeun "Menu" "Setup Mesin" "Pulse".

Pariksa naha pulsa sumbu XYZ bener.

00:14:53,811 - 00:14:56,684

Parameter pulsa di dieu leres.

00:14:57,449 - 00:15:05,511

Upami pulsa sumbu XYZ nyaéta 400.

Mangga wartosan insinyur pikeun ngarobih parameter.

00:15:07,213 - 00:15:11,720

Ayeuna urang pencét tombol "Batalkeun" pikeun uih deui ka antarmuka utama.

00:15:12,658 - 00:15:17,165

Pencét tombol "HOME" pikeun mulangkeun mesin ka asal mékanis na.

00:15:21,208 - 00:15:25,715

Mesin bakal otomatis balik deui ka pojok kénca handap desktop.

00:15:36,665 - 00:15:41,172

Teras anjeun tiasa pencét XYZ + - pikeun ngadalikeun arah gerak mesin.

00:15:52,954 - 00:15:58,954

Saatos mesin bisa mindahkeun normal.

Pindahkeun sumbu X ka tebih kénca.

00:16:16,218 - 00:16:20,792

Arah saklar ka katuhu. Hurungkeun mode laser.

00:16:31,878 - 00:16:37,071

Mesin bakal otomatis ngalih ka pojok katuhu luhur desktop.

00:17:00,159 - 00:17:04,461

Lajeng balik deui ka posisi awal karya laser panungtungan.

00:17:23,345 - 00:17:27,558

Mindahkeun posisi sirah laser ngaliwatan controller laser.

00:17:48,848 - 00:17:53,738

Pastikeun yén cai cooling tina tube laser circulates normal.

00:18:14,373 - 00:18:16,776

Daya dina pompa hawa leutik.

00:18:29,874 - 00:18:33,582

Sambungkeun outlet hawa ka posisi sirah laser.

00:18:44,443 - 00:18:47,438

Paké acrylic pikeun adjustment jalur lampu.

00:18:56,745 - 00:18:59,918

Ngalereskeun akrilik dina pemantul ka-1.

00:19:09,502 - 00:19:12,497

Pencét tombol "Pulse" dina controller.

00:19:28,865 - 00:19:32,929

Pariksa naha laser nu keur bersinar dina puseur eunteung.

00:19:45,039 - 00:19:46,697

Nguji kaca spion ka-2.

00:20:13,970 - 00:20:18,301

Pastikeun yén laser illuminates puseur kaca spion 2nd.

00:20:29,233 - 00:20:39,891

Lamun laser teu nyaangan puseur eunteung 2nd.

Saluyukeun screw tina eunteung 1st mun ngantep laser nyaangan puseur eunteung 2nd.

00:20:47,002 - 00:20:51,206

Saluyukeun pemantul luhur sirah laser.

00:21:05,454 - 00:21:10,974

1st lajeng sirah laser ka tebih katuhu tina mesin. (Deukeut kaca spion 2)

00:21:20,034 - 00:21:23,692

Pencét "Pulse".

Ngaduruk titik.

00:21:32,335 - 00:21:37,746

Mindahkeun sirah laser ka tebih kénca.

Jauh tina kaca spion ka-2.

00:21:42,825 - 00:21:46,660

Pencét "Pulse".

Ngaduruk titik sejen.

00:21:50,581 - 00:21:53,894

Upami 2 nembak henteu dina posisi anu sami.

00:22:04,943 - 00:22:07,989

Saluyukeun screw tina kaca spion ka-2.

00:22:22,680 - 00:22:24,835

Tes seuneu deui.

00:22:39,993 - 00:22:47,027

Nya kitu, 1st mindahkeun sirah laser ka sisi katuhu mesin.

Pencét "Pulse".

00:22:53,661 - 00:22:59,380

Lajeng mindahkeun sirah laser ka sisi kénca mesin deui.

Pencét "Pulse".

00:23:31,932 - 00:23:35,067

Ngan nempatkeun 2 nembak dina posisi anu sarua.

00:23:48,334 - 00:23:55,657

Laser kudu disinar dina posisi anu sarua dua kali.

Lengkepkeun setelan laser di dieu.

00:24:32,073 - 00:24:34,315

Lajeng saluyukeun laser dina nozzle nu.

00:24:44,385 - 00:24:48,100

Paké pita pikeun nempel kana nozzle nu.

Pencét "Pulse".

00:24:58,954 - 00:25:01,911

Pariksa naha liang aya di tengah nozzle nu.

00:25:23,784 - 00:25:27,751

Saluyukeun screw tina kaca spion ka-3.

00:25:28,374 - 00:25:41,667

Nguji deui

00:26:25,064 - 00:26:31,673

Nepi ka makéna laser ti puseur nozzle nu.

Ngalengkepan setelan jalur laser.

00:26:45,549 - 00:26:47,672

Uji laser ukiran.

00:27:02,196 - 00:27:06,209

Paké kabel USB pikeun nyambungkeun mesin ka komputer.

00:28:09,854 - 00:28:15,038

Pasang parangkat lunak kontrol laser - RDWorks V8.

00:28:44,385 - 00:28:47,457

1st install supir USB.

00:29:09,764 - 00:29:17,291

Teras pilih posisi dimana sirah laser mulang ka asal.

Mesin ieu aya di katuhu luhur.

00:29:22,363 - 00:29:23,510

Klik "Pasang".

00:29:25,648 - 00:29:26,427

Klik "Kaluar".

00:29:38,878 - 00:29:41,042

Buka software laser "RDworks V8"

00:29:49,812 - 00:29:54,115

Dina "USER". "Baca" parameter dina mesin.

00:30:03,807 - 00:30:12,743

Lamun teu bisa dibaca. Pariksa naha kabel USB disambungkeun bener atawa naha controller laser dihurungkeun.

00:30:19,556 - 00:30:25,284

Teras lebetkeun setélan vendor.

Sandi nyaeta "rd8888".

00:30:27,071 - 00:30:29,324

Baca sadaya setelan dina mesin

00:30:47,995 - 00:30:56,575

Lajeng dina setélan sistem. Atur lokasi imah jeung posisi sirah laser. Katuhu luhur.

00:31:09,361 - 00:31:13,799

Lebetkeun téks atanapi grafik. Saluyukeun ukuranana

00:31:35,910 - 00:31:41,562

Pencét dua kali. Setel laju, sapuan, kakuatan, sareng Interval.

00:31:59,353 - 00:32:04,190

klik pikeun ngundeur". Mindahkeun file ka mesin.

00:32:09,295 - 00:32:12,350

Mindahkeun sirah laser ka posisi keur engraved.

00:32:21,948 - 00:32:29,013

Pencét tombol "Asal" dina kadali.

Setel posisi ayeuna salaku posisi awal karya.

00:32:31,325 - 00:32:34,380

Pencét "Pigura" pikeun pariksa ukuran ukiran.

00:32:44,995 - 00:32:52,388

Tetep nozzle ngeunaan 10mm jauh tina bahan.

Ieu panjang fokus laser nu.

00:33:08,720 - 00:33:10,856

Pencét "Mimitian" dina controller.

00:34:04,530 - 00:34:06,844

Pindah modeu router CNC.

00:34:19,895 - 00:34:22,209

Pindahkeun laser ka tebih katuhu.

00:34:30,967 - 00:34:33,014

Cabut pompa hawa.

00:34:42,716 - 00:34:44,941

Arah saklar ka kénca.

00:34:55,935 - 00:35:01,368

Sadaya sumbu balik deui ka asal mékanis.

Kabéh sumbu imah.

00:35:30,618 - 00:35:34,625

Anggo piring tekanan pikeun ngalereskeun bahan anu bakal diukir.

00:36:33,659 - 00:36:36,419

Ngalereskeun alat ka spindle nu.

00:37:18,737 - 00:37:24,972

Pindahkeun alat ka posisi dimana anjeun kedah ngamimitian ukiran.

00:37:40,993 - 00:37:47,851

Pencét "XY-0" dina controller. Setel asal gawé sumbu XY.

00:37:53,307 - 00:37:58,773

Lalaunan mindahkeun sumbu Z (alat) kana beungeut bahan.

00:38:01,668 - 00:38:05,396

Pencét "Z-0" pikeun nyetél asal kerja sumbu Z.

00:38:05,396 - 00:38:12,682

Posisi kerja sumbu Z ogé tiasa diatur sacara otomatis nganggo sénsor alat.

00:38:14,999 - 00:38:24,602

Teundeun sénsor alat dina luhureun bahan anu bakal diukir.

Sakaligus pencét "Menu jeung ON / OFF" dina controller nu.

00:38:46,180 - 00:38:53,734

Nalika alat némpél sénsor alat, éta otomatis naék. Pangukuran réngsé

00:39:01,884 - 00:39:04,626

Teras anjeun tiasa ngajalankeun file ukiran laser.

00:39:15,215 - 00:39:20,274

Nalika ngukir batu. Hurungkeun pompa cai cooling alat.

00:40:04,363 - 00:40:10,669

Saatos adjustment laser réngsé. Pasang panutup pelindung di sisi katuhu.

00:40:39,848 - 00:40:45,123

Majelis parantos réngsé.

Hatur nuhun ningali.